Contact Us for more information.
Hardware Products
|
To compliment our services , we stock and supply a range of fasteners and fixings for attaching other materials and products to steel .
For more information click here
|
|
Used to secure bricks to frame work. Clips onto stud flange with a light tap with a trowel. Available in galvanised and stainless steel.
|
|
Snaps into 32mm service holes for running plumbing pipework through the framework to separate the metals and support pipes to prevent hammering.
|
|
Snaps into 32mm punched service holes to insulate electrical wires from steel framing and to provide a rounded edge for easier wiring installation.
|
|
Used to fix insulation to steel frames.
Will not tear or damage foil during installation.
|
|
These piers allow for height adjustment in floor systems. They will allow you to get your floor level and keep it level if any ground movement occurs.
|
|
Made to fit inside a 75mm column, used to tie down the column.
|
|
Made to fit inside a 90mm column, used to tie down the column.
|
|
Ties down columns in car ports, verandahs etc.
Also hides all those ugly bolts and screws under a decorative cover.
|
|
Provides a brace to offset posts or can be purely decorative.
Available in different shapes.
Click here for more shapes
|
|
Provides a seemless, clean look to door jambs.
Click here for more information
|
|
Made to finish off wall ends.
Click here for more information
|
|
Create seemless, clean window sills.
Click here for more information
|
|
Metal cavity sliding door frames with a timber exposed edge to suit 75 and 90mm metal studwork. Common sizes are kept in stock and most other sizes available on order.
|
|
This bracket is used to horizontally stiffen the top of non loadbearing internal walls by connecting them to the roof system (mostly trusses), but still allow for verticle deflection (slab/floor movement and truss/roof structure flexing under load).
|
|
These brackets are custom made to suit individual jobs. They come in a range of sizes, shapes, angles, and pitches.
Commonly used in the connection of exposed Boxspan members in Verandahs , Pergolas and car ports. Galvanised material suitable for powder coating.
|
Roofing Products
|
The Ridge/Hip Tie is a special Custom Steel Frames structural member.
It provides two 40mm ridge battens, a lip for roof battens to be fastened to and a folded safety edge.
|
|
This member is a Valley Support Tray to support a Lysaghts or equivalent Valley Tray (colourbond or zinc). It provides two 40mm Valley battens, a lip for roof battens to be fastened to, a folded safety edge and grooves to prevent sweating between the 2 members.
|
|
19mm top hat batten 0.42 thick with serrated top and safety edge.Primarily used as a ceiling sheet connection under trusses. Other uses include wall cladding battens, eave battens, bottom chord tie and electrical cable tray through trusses.
|
|
40mm top hat batten 0.55 for general use on roofs , walls , fences , floors. Features mitre cut ends , serrated non skid top and a safety edge.
|
Framing Products
|
We can supply your frame in flat pack form. Usefull for remote sites.
|
|
Used as a general joiner between steel framing members.
Available 1.2mm thick in three sizes -
-
32mmx32mm
- 67mmx67mm
- 60mmx75mm
|
|
Used as the top cord of our walls and roof trusses.
Optional 32mm service holes.
75mm or 90mm widths, in 1.0 or 1.2mm thickness.
Lengths to order.
|
|
Rolled to fit inside our Top Plate material.
Optional 32mm service holes.
75mm or 90mm widths, in 1.0 or 1.2mm thickness.
Ends can be crimped.
|
|
Rolled to fit inside our Stud material.
75mm width, in 1.0 or 1.2mm thickness.
Lengths to order.
|
|
Rolled to fit inside our Top Plate material.
Optional 32mm service holes.
75mm or 90mm widths.
Lengths to order.
|
Structural Products
|
Galvanised
Widths from 100mm to 250mm.
1.2-1.9mm thickness
Suitable for floor joists, Rafters and general use when screw fixing.
Lengths to order.
|
|
Galvanised
To suit purlin sizes.
Suitable for floor bearers, carports and roof construction
|
|
TrueCore
Widths from 100mm to 250mm.
Suitable for floor joists, Rafters and general use when welding.
Lengths to order.
|
|
TrueCore
To suit purlin sizes.
Suitable for floor bearers, carports and roof construction
|
|
H bracket is a pre fabricated purpose built CSF bracket to connect a 100,150mm,200 or 250mm high member typically a C purlin to the top of a studwork wall.
Typically used in overhang situations on eves and gables where tie down is important . Can be bolted for extra security and has 6 screws in shear to both members.
|
|
Uncoated
Available in many sizes square or rectangular.
Suitable for columns or any light structural application.
Should be appropriately painted or powdercoated.
|
|
Available in sizes from 100mm to 250mm.
Suitable for carports, pergolas and other outdoor applications.
Looks fantastic when powdercoated and assembled using our bracket system.
|
|
Duragal
Available in many sizes square or rectangular.
Suitable for columns or any light structural application where screw connections are used.
Suitable for welding.
Pre-galvanised.
|
|